• 地址:济南市槐荫区鑫苑世家公馆2号楼2603室
  • 电话:0531-87568508 /
  • 手机:18653128690
  • 邮箱:jnyhrs@163.com
  • 实验室高效送风口安装要注意什么?
    来源: 浏览: 发布日期:2018-08-23
    高效送风口的安装注意事项:
    Matters needing attention in installation of high efficiency air supply outlets:
    1.在安装高效送风口前需要先清洗好产品,并且要对洁净室进行全方位的清洁,如果净化空调系统中有灰尘,要进行清扫清除,需要达到清洁要求的标准才能清洁夹层或者吊顶内部,再次净化空调系统后必须要试运转连续12h以上,才能做再一次的清洁处理。
    1. Clean the product before installing the high-efficiency air supply outlet, and clean the clean room in an all-round way. If there is dust in the air-conditioning system, it needs to be cleaned and cleaned. It needs to reach the standard of cleaning requirements to clean the interlayer or ceiling interior. After the air-conditioning system is cleaned again, it must run for more than 12 hours continuously. In order to do the cleaning again.
    2.安装前大家首先要知道的一点是,高效送风口的尺寸效率要求,必须要符合洁净室现场的设计要求及客户的标准。
    2. The first thing we should know before installation is that the dimension and efficiency requirements of high-efficiency air supply outlet must meet the design requirements of clean room site and customer standards.
    3.高效送风口在安装之前,需要现场对送风口的包装进行检查,检查内容包括滤纸、密封胶以及框架,看这些东西有无损坏的情况;边长、对角线和厚度尺寸是否符合大家的要求;框架上有无毛刺和锈斑;产品是否有合格证,技术性能是否符合设计的要求。
    3. Before the installation of the high-efficiency air supply outlet, it is necessary to inspect the packaging of the air supply outlet on the spot, including filter paper, sealant and frame to see if there is any damage to these things; whether the side length, diagonal line and thickness meet our requirements; whether there are burrs and rust spots on the frame; whether the product is qualified, Technology Does the performance meet the design requirements?

    空气净化工程
    4.高效送风口的安全运输需要严格按照生厂家的标志说明来放置,在运输的过程中需要轻拿轻放切忌不要剧烈振动和碰撞。
    4. Safe transportation of high-efficiency air supply outlet should be placed strictly according to the manufacturer's logo. In the process of transportation, it should be handled lightly and avoid violent vibration and collision.
    5.进行高效送风口检漏,检查和检漏产品是否合格,安装时要根据各台送风口阻力的大小进行合理的调配,对于单向流的送风口,同一风口或者送风面上的滤器之间,每台额定的阻力和各台平均阻力相差要小于5%。洁净度的级别要等于或高于100级洁净室的高效送风口。
    5. Check the leakage of high-efficiency air supply outlet, check and check whether the product is qualified, install according to the size of the resistance of each air supply outlet reasonable allocation, for unidirectional flow air supply outlet, between the same air outlet or the filter on the air supply surface, each rated resistance and the average resistance difference between each set should be less than 5%. The cleanliness level should be equal to or higher than that of the 100 level clean room.
    7.洁净室内需要安装高效送风口的风口翻边和吊顶板之间的接缝要施行密封垫处理,有裂缝的地方必须要严格的处理好。如果高效送风口损坏或涂层破损不得再进行安装,送风口和风管在安装时必须要严格的连接好,开口端用的是塑料薄膜和胶带加固密风处理。
    7. Clean room needs to install high-efficiency air supply vent flanging and ceiling joints between the implementation of gasket treatment, cracks in the place must be strictly handled. If the high-efficiency air supply outlet damage or coating damage can not be installed again, the air supply outlet and air duct in installation must be strictly connected, the opening end is reinforced with plastic film and tape dense air treatment.
    有了空气净化工程上面的小总结,希翼对广大客户有所帮助,如果有什么不理解的或者寻求帮助的请点击大家的官方网站:或者来电咨询,大家会尽全力为您解决
    With the summary of the air purification project above, I hope it will be helpful to our customers. If you have any incomprehension or ask for help, please click on our official website: or call for advice. We will try our best to solve it for you.
    XML 地图 | Sitemap 地图